“Every spring on every garage door will break,” says Jim Rice, owner of Broad Ripple Overhead Doors & Openers in Indianapolis. “After so many thousand times up and down, it gets metal fatigue and snaps. At least once a year, you should disconnect the garage door springs and lift the door up manually to see how well it’s balanced. Unless you hear metal screeching or something breaks, you don’t need us.”

Through our garage door configurator by Clopay, you can design, visualize and purchase a new Clopay garage door. Upload a photo of your home and then browse the configurator to see which style works for you. Choose from a variety of designs, textures, colors, finishes, window options and decorative hardware. You’re able to easily and quickly see the transformation, and then make it a reality.
Containment cables. When old extension springs break, the springs and cables become heavy whips that damage cars and even injure people. To solve the whipping problem, manufacturers now offer containment cables that run through the center of side-mounted extension springs. If you have extension springs and don’t plan to replace your door, make sure the springs have these containment cables, or have a professional install them.
If you've installed a replacement door or two around your home, it seems pretty simple -- all it takes is tightening a couple of screws and you're done. Installing t­he largest door in your house, however, is not quite so simple. Garage door in­stallation, whether manual or automatic, can be difficult and dangerous. Manual garage door installation is much easier than automatic garage door installation, but the one you choose generally depends on what kind of door you have.
The history of the garage door could date back to 450 BC when chariots were stored in gatehouses, but in the U.S. it arose around the start of the 20th century. As early as 1902, American manufacturers—including Cornell Iron Works—published catalogs featuring a "float over door." Evidence of an upward-lifting garage door can be found in a catalog in 1906.[4]

Squealing, screeching, or grinding noises from your garage door are usually indicative of a lack of lubricant or an accumulation of dirt or debris in the tracks. When removing debris, do not use harsh chemicals to clean the tracks. Once the track is clean, coat it with lubricant designed especially for garage doors, if possible. If you do not have access to this special type of lubricant, you can use WD-40 on the tracks and hardware.
Repair Sagging Garage Doors – As doors and homes age, they can shift and move and sometimes this results in a garage door that needs to be realigned or reinforced. We will send a technician to your home to adjust the doors and to inspect the entire opening to make sure the door isn’t damaged. Once we understand the problem, we will fix the needed parts and make any adjustments to the door.
In many homes, the original garage door was installed during construction of the garage and the builder may have chosen the least expensive model. Decades later, the homeowner may decide to upgrade to a higher quality door. While appearance and cost will likely be the biggest considerations for most homeowners, other factors such as insulation value, ease of operation and safety features should also be considered. A highly rated garage door installation professional can offer more detailed advice.
"I was very impressed with how quickly they responded to my request and Gabe's willingness to help! We had a 16 year old garage door opener that was problematic and wanted to replace it with a new smart garage door opener (upgrade) Everyone else we contacted either wanted a trip charge just for an estimate, or the earliest they could come out was 10 days to 2 weeks later. After not being able to shut our garage door again yesterday I was fed up and wanted it fixed NOW. Gabe came out and explained that the door wasn't closing right because the spring was improperly tensioned and showed us how the door should be balanced when halfway open. He then gave us choices. He could do the adjustment to the spring and adjust the old opener and we could probably get a couple more years out of it. He could install the new smart opener we had purchased already for us, although he couldn't warranty it for us because it was purchased elsewhere. Or he could install a new smart opener that he had brought with him and adjust the spring while doing that. We went with the 3rd option and he was finished in about an hour and a half. Everything works great now, no more issues. And if we do have an issue I know they can fix it same day or at least next day instead of 1-2 weeks later like everyone else. The only reason I didn't give them 5 stars is because his price was much higher than all of the other install quotes we dad (including the opener and laber). However, I understand that he had to get his markup on the garage door opener he had purchased and it was worth the extra money to us for the immediate service and just to have the project done and over with. Also I wanted to know how to get the opener to work on my smart phone and link it to my car and Gabe couldn't help me with either of those. He couldn't even tell me which of the MyQ apps in the list of 6 of them on my phone to install so I was on my own there. Another reason I didn't do 5 stars. I was able to get the app installed, although it was the second one I tried and it is connected and works now. But I still can't get it to work in my car so I guess I'll have to use the actual remote. Still we are satisfied with the job and would definitely recommend Elite Garage Doors. "
A garage door is a large door on a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling. Larger doors are usually made in several jointed panels that roll up on tracks across the garage ceiling, or into a roll above the doorway. The operating mechanism is spring-loaded or counterbalanced to offset the weight of the door and reduce human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss. Warehouses, bus garages and locomotive sheds have larger versions.
Because garage doors are large, heavy, and mildly complicated, most people who buy them take advantage of these services. But, if you’re pretty adept at DIY tasks, you can save some money and enjoy the satisfaction of doing the job of installing a sectional garage door yourself. (Sectional garage doors travel up and down on rollers that ride along tracks at each side of the garage doorway.)
Garage door manufacturers typically produce garage doors fitted with torsion springs that provide a minimum of 10,000 to 15,000 cycles and are guaranteed for three to seven years. One cycle is a single opening and closing sequence. Most manufacturers offer a 30,000 cycle spring. However, it is important to remember that if the weight of the garage door is increased by adding glass, additional insulation, or even several coats of paint, the life of the torsion spring may be greatly reduced. Additionally, springs at highly humid environments, such as coastal regions tend to have a significantly shorter cycle life, due to the corrosive cracking.
Safe automatic door openers. All automatic openers must now have an auto-reversing mechanism and photoelectric eyes located near the floor on both sides of the door (see photo). If the door is closing and the beam between the eyes is interrupted, the door will automatically reverse. If the eyes aren’t connected, the door won’t operate. For instructions on how to install a new garage door opener, see How to Install a Garage Door Opener.
"The doors, tracks and openers were installed in a few hours. They look great and add so much to our exterior as well as quiet and warmer in the garage. The technicians tweaked the pad installation as we needed. They were on time, professional and courteous. I give them 5 stars. My only ding on performance was filling up our rolling recycle bin with intact noses that we had to pull out and break down. I thought the boxes would have been hauled away."
One of the last safety features on a garage door system is the manual release mechanism. Designed to disengage the garage door from the opening system should entrapment, a power outage or other malfunction occur, the manual release mechanism is most commonly found on the track that runs from opener to the garage door. It’s usually a bright red handle that should hang no higher than 6 feet off the ground.

The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.

Carriage: These doors mimic the look of doors found on old carriage houses in the days of horses and buggies. Because of their rustic look, they are often favored in the West and Southwest of the United States. The doors swing open like oversized French doors and hang from jambs on hinges. With their unique look, they create an area of visual interest for your home and are quite energy efficient. The downside is they require a considerable amount of clearance to work properly. Because most carriage garage doors are largely composed of wood, you may need to replace deteriorating or rotting door materials. The average cost for carriage garage door repairs is $133.
Thank you, thank you, thank you for sharing your knowledge. I just replaced our shower cartridge and our leak is FIXED!!!!!!! Your instructional was clear and concise. I did purchase 2 cartridges first, because I did not know the type it was and could not pull it out without the plastic cover it comes with. Fortunately, it was one of the two. By the way I'm a 63 year old woman. If I can do it, anyone with internet and a little patience and an hour can do it.....
Trusted Professionals: Thirty-plus years is a long time to provide damaged garage door repair service in Bakersfield, and we’ve learned a lot through our extensive experience. Each of our team members knows garage doors inside and out, and each can provide service on any make or model. You know you’re in good hands because of King Door’s long history in this area, and each of our technicians reinforces their knowledge by quickly analyzing your issues and making expert recommendations on the best way to proceed.
John, the service tech, was able to show up 2 hours ahead of schedule which worked out great. He knew the problem and readily offered a fix to repair the contractor grade spring and roll bar to a heavier duty version. Repair was done in a short period time and I could not be happier with the end result. He was friendly and knowledgeable and cared about getting it done right. Very pleased with the work and warranty.
Sears garage repair technicians are fast, with same-day, emergency repairs available in most areas. We can replace garage door broken springs, rollers, cables, hinges, sensors and weather seals. We can also adjust garage door tracks and springs to make sure your door operates smoothly. Having problems with your garage door opener? We can repair or replace that too. Check out our line of Craftsman Garage Door Openers. Craftsman is America’s #1 brand of garage door openers! 1
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
When you buy a new garage door, you are really hiring a garage door installation company. You will rely on that company for everything from advice on brands, insulation, material, features to an expert installation and may use them for years to come. You should be able to trust your garage door company with keeping you and your family safe and keeping your garage door working perfectly all year long. Let the experts at Precision Door show you why we are the best in the business, with our fast quality service, commercial grade parts, and friendly technicians you can trust.
Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
×