When your home or business depends on garage door repair in Bakersfield for everyday convenience, security, and dependability, the need for repairs can be a serious slowdown in your life. That’s why King Door Company offers Kern County residents and business the best garage door repairs and other services, completed by a team of expert professionals who can quickly and effectively fix garage doors in Bakersfield and the surrounding communities in Kern County.
Electric Garage Door Openers – Service and repair of the electric garage door opener itself, including the lift mechanism that pulls the door up and guides it down. This is typically not part of the garage door itself and is serviced and repaired on its own interval. Typical service includes inspection, repair, adjustment, and lubrication if needed. Also, we typically inspect the mounting of the unit as well as its attachment to the door itself.
Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
Roller doors ("Sheet Doors"-USA) are usually constructed of corrugated steel. They evolved from cover window and door coverings.[4] Other materials can be used (e.g.; transparent corrugated fibreglass) where strong impact resistance is not required. Corrugations give the door strength against impacts. A typical single car garage roller door has a preloaded spring inside the rolling mechanism. The spring reduces the effort required to open the door. Larger roller doors in commercial premises are not sprung (except USA) and use a manual pulley and chain system or a geared motor to raise and lower (roll up and roll down) the door. Roller doors cannot be effectively insulated.
Operating since 1998, we are a family-owned company which all your garage door needs. In our years of operations, our clients have strongly benefitted from our efficiency and reliability. This is why we are simply the best in what we do as evidenced by our consistent Yelp 5 Star rating, A+ rating from BBB and Super Service Award from Angie’s List. You can trust that our work is done with quality as we are licensed, bonded and insured and is in the roll of Arizona’s Registrar of Con-tractors. Furthermore, you can be sure that all of our technicians passed rigorous training and our battery of background checks.
I have recently purchased a house with an older roof that needs to be restored soon. So, I am trying to decide on I should go with a metal roof other than shingles. If I install metal roofing over solid decking such as OSB or plywood, integrate with a properly insulated garret, there is very little noise difference compared to standard asphalt shingles. I have briefly read benefits and drawbacks of Metal roofing but as I listed before I should go to metal roofing and hiring a roofing contractor no matter its expensive or noisy anyhow, Your article has cleared a lot of misinterpretation I’ve had before.

Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware. 

Annual maintenance. Make an annual check of all nuts and bolts on rails and rollers to make sure they’re firmly tightened. Check the condition of all cables to make sure they’re not worn or frayed. Lubricate rollers and springs with a garage-door lubricant (see How to Fix a Noisy Garage Door for maintenance and problem-solving tips). The door should operate smoothly and be properly balanced. Check the balance by disconnecting the opener and lowering the door halfway- the door should hold its position. If it doesn’t, adjust the spring tension or replace the springs.

A torsion spring counterbalance system consists of one or two tightly wound up springs on a steel shaft with cable drums at both ends. The entire apparatus mounts on the header wall above the garage door and has three supports: a center bearing plate with a steel or nylon bearing and two end bearing plates at both ends. The springs themselves consist of the steel wire with a stationary cone at one end and a winding cone at the other end. The stationary cone is attached to the center bearing plate. The winding cone consists of holes every 90 degrees for winding the springs and two set screws to secure the springs to the shaft. Steel counterbalance cables run from the roller brackets at the bottom corners of the door to a notch in the cable drums. When the door is raised, the springs unwind and the stored tension lifts the door by turning the shaft, thus turning the cable drums, wrapping the cables around the grooves on the cable drums. When the door is lowered, the cables unwrap from the drums and the springs are rewound to full tension.[7]
Adding insulation to a hollow garage door can help heating and cooling costs and reduce noise. However, the most important thing to consider is how much weight you are adding to the door. The springs on a garage door are specific to the size and weight of the door, and adding weight to the door without changing the springs can damage them and wear out gears faster in the electric operator. Also, adding a strut across the door might be necessary to make sure the door doesn’t buckle when in the horizontal position.
Lower the door and dismantle it by removing the hardware. Lower a double door by recruiting at least two helpers to help with the weight, and place a 2×4 block under the door to prevent smashing a foot or finger when it’s lowered. Remove the sections one at a time by disconnecting the rollers and brackets. If you have windows, tape them to help control flying shards if they break. Then remove the old roller tracks and remaining hardware.
With over 300 independently moving parts, your garage door is a deceptively complex piece of equipment. To help prevent malfunctions and break-downs, it is a good idea to occasionally perform a garage door tune-up to keep all of these parts in good working order. A regular tune-up service by a Sears professional can prevent unexpected door problems and prolong the life of your existing equipment.
Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
Our highly skilled technicians are specialists in every aspect of garage door repair including broken springs, rollers, and door remotes as well as garage door opener replacement and new door installation. We offer 24/7 services throughout Gwinnett, North Fulton, Cobb, Cherokee, Forsyth, Hall, North DeKalb, Barrow, Bartow, Dawson, Gilmer, Gordon, Lumpkin, Pickens, Walton and Whitfield Counties.

Hmmm...Intro to E12...looks suspiciously like a freehand angled cut on that contractor saw... Yes, the riving knife might save you from a dangerous kickback...but still a very bad idea.. Why not a 'safety segment' explaining kickback and why you should not do this (styrofoam demo, back side of the blade teeth rising up grabbing the foam and throwing it back at you...)
The Garage Door Remote prevents hacking and provides The Garage Door Remote prevents hacking and provides peace of mind with Security+2.0 the highest level of encryption. Control up to three brands of garage door openers at once with this easy-to-program three-button remote. Compatible with nearly every garage door opener made by Chamberlain LiftMaster and Craftsman it’s the easy ...  More + Product Details Close
Aluminum garage door styles are similar to steel doors except that they weigh much less.  This prevents them from providing a great deal of insulation and they do tend to dent easily.  However, Aluminum is one of the least expensive garage doors that can be purchased for the home, they have a long lasting finish that does not rust easily and it is available in a faux wood texture that can complement the home’s overall look.
Hmmm...Intro to E12...looks suspiciously like a freehand angled cut on that contractor saw... Yes, the riving knife might save you from a dangerous kickback...but still a very bad idea.. Why not a 'safety segment' explaining kickback and why you should not do this (styrofoam demo, back side of the blade teeth rising up grabbing the foam and throwing it back at you...)

Garage Door Service Company

×