The tech that serviced your door must not understand simple mechanics. The tracks do not move, so they do not need to be lubricated. All that does is make a mess. The rollers and hinges DO move, so it is logical to lubricate them, at the hinge barrel or pivot point, and in the little area near the stem of the rollers where you can see the bearings. Adding a bit of lube to the torsion spring also cuts down on the friction between the coils and makes the spring glide easier. However, too much will make it spritz out lube as the door opens and closes, and that it less than desirable. Same thing for pulleys on an extension spring door.
Install the vertical roller tracks first by wrapping the curved lip around the rollers. The top of these tracks should be approximately 8 in. below the top of the top section. Wait to install the upper tracks until this step is complete. Check the level of the top section to make sure the tops of the vertical roller tracks are level with each other. The bottom of the roller tracks should be at least 1/8 in. off the concrete floor. After leveling and mounting these tracks, install the upper roller (horizontal) tracks.
A typical version of an overhead garage door used in the past would have been built as a one-piece panel. The panel was mounted on each side with unequal parallelogram style hinge lifting mechanism. Newer versions of overhead garage doors are now generally built from several panels hinged together that roll along a system of tracks guided by rollers. The weight of the door may be 400 lb (181.4 kg) or more, but is balanced by either a torsion spring system or a pair of extension springs. A remote controlled motorized mechanism for opening garage doors adds convenience, safety, and security.
There is no cost because Precision will send a technician to your home for a "repair estimate". A "repair estimate" allows our technician to evaluate your garage door and determine why it is not functioning properly. Then provide you with a repair estimate with the cost to get your garage door operating correctly. The choice is yours to proceed with the work on the repair estimate or if you decide not to proceed with the work then there is no cost to you.
Using your drill, add tension to the torsion spring. This system uses a single spring for a double door, but many manufacturers use two springs for a double door. The painted line on the spring acts as a gauge for the number of turns you put on the spring. To keep the bar from turning while you’re adding tension, attach a locking pliers to the bar on both ends of the spring. Apply lubricant for garage doors to the spring.
Test the door balance. A garage door should require only a few pounds of pressure to move it up and down. If springs wear out and lose their resiliency, a power garage door opener may need to work extra hard to lift the door. This can quickly wear out the motor on the opener. Replacing worn-out springs is usually a job for a professional technician.
When you buy a new garage door, you are really hiring a garage door installation company. You will rely on that company for everything from advice on brands, insulation, material, features to an expert installation and may use them for years to come. You should be able to trust your garage door company with keeping you and your family safe and keeping your garage door working perfectly all year long. Let the experts at Precision Door show you why we are the best in the business, with our fast quality service, commercial grade parts, and friendly technicians you can trust.
When it comes to installing garage doors and openers, The Home Depot has an unbeatable team of professionals dedicated to making sure your garage door project runs smoothly from start to finish. Your new garage door can be customized with a variety of features like unique color choices, window styles and hardware upgrades. We also offer options for your garage door opener including Smartphone control, Wi-Fi, battery back-up. The Home Depot installs garage doors and garage door openers with extended warranties that go beyond industry standards. Contact us today for a free in-home consultation.
Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
Torsion springs have three advantages over extension springs: They’re quieter, safer and easier to fine-tune. Torsion springs are quieter because you don’t have a spring knocking against a roller track. They’re safer because when a spring breaks, it usually stays on the bar. Finally, you can fine-tune the tension on a torsion spring so the door is perfectly balanced. Setting the tension on torsion springs has always been very dangerous, but torsion and extension spring systems with easy, do-it-yourself tensioning (Photo 7) are available. If you don’t use one of these DIY-friendly, easy tensioning systems (Clopay EZ-Set Spring and Wayne-Dalton TorqueMaster are two brands), you should hire a professional to release and set the tension on a torsion spring.
No matter what kind of door you are installing, be very careful. The instructions that follow are merely guidelines. You should read your garage door manufacturer's instructions and owner's manual very carefully before attempting either type of installation. And if you're a do-it-yourself greenhorn, skip this project and hire an experienced professional. It may be more expensive, but garage door installation is on the higher scale of DIY difficulty.
After a full inspection of your overhead garage door system and door opener, we will recommend different solutions so you can assess which one best fits your needs and budget. Our friendly technicians are skilled and certified for any size job, plus, our work is backed by great warranties on quality guaranteed parts and brands as well as our own warranty on workmanship.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
I was impressed by the expertise the technician demonstrated. The service was fast and professional. The technician was at my house only a few hours after calling to schedule an appointment, and the on the spot same day service was remarkable. The technician was professional, friendly, and extremely knowledgeable. I highly recommend Precision Overhead Garage Door to anyone in need of garage door repair.read more
Installing an overhead garage door requires a few tools and a friend to help. First, the lower door panel needs to be set up in the center of the doorway. The remaining panels and tracks are held in place with hinges, brackets, and screws. Set up an easy-to-install torsion spring system to ensure that your door lifts properly for many years to come.
A garage door is a large door on a garage that opens either manually or by an electric motor (a garage door opener). Garage doors are frequently large enough to accommodate automobiles and other vehicles. Small garage doors may be made in a single panel that tilts up and back across the garage ceiling. Larger doors are usually made in several jointed panels that roll up on tracks across the garage ceiling, or into a roll above the doorway. The operating mechanism is spring-loaded or counterbalanced to offset the weight of the door and reduce human or motor effort required to operate the door. Less commonly, some garage doors slide or swing horizontally. Doors are made of wood, metal, or fiberglass, and may be insulated to prevent heat loss. Warehouses, bus garages and locomotive sheds have larger versions.
Safety Inspections: Garage doors operate under a massive amount of tension. It’s the tension that makes a garage door work properly, but this tension can also pose a threat when the garage door is out of order. To ensure that your garage remains a safe place, we provide an annual, 14-point safety inspection. This can pinpoint problem areas before they spiral out of control and help you prevent costlier repairs after something goes wrong.
A garage door has a huge impact on your home. It’s the largest moving part of your home. it’s more than a garage door though, it’s also the second front door to your home. It enhances the curb appeal, energy efficiency, and security for your home. Don’t trust anyone else but the experts at Overhead Door Company of Pueblo™. We are the best garage door repair and service company in the Pueblo area, with the most experienced, professional, and courteous technicians. Our team of garage door technicians will repair all your broken springs, openers, and doors! When you’re ready to give your home a makeover, Overhead Door Company of Pueblo™ has the highest quality garage doors in the area.
We have the best team of expert professionals who know how to handle each and every type of garage door and its components. This is because all of our technicians go through a rigorous training process, covering every known garage door repair technique. We do not let them onto the field until we know that they are completely trained, and can perform a job to perfection. Aside from this, they are continually updated with all the latest knowledge, information and training in order to do their work efficiently.
Just in case you still want to know: You could glue foam panels to the inside of the door, but it would be better to just pressure fit them in place to avoid the weight of the glue. Any weight that you add to the door has the very real potential to unbalance the door. If the springs were a little "hot" or strong to start with, it may not be a bad thing to add weight. If the springs were the right ones, even a few pounds will un-balance the door. If they were too weak to start with, any additional weight is going to make it worse.
The Overhead Door Company of Pueblo™ has been proudly serving customers since 1957. We invented the Overhead Garage Door, and have earned our position as the number one choice for garage door in Pueblo. The Overhead Door Company of Pueblo™ takes pride in our quick, courteous, and professional specialists who will repair your garage door problem, anywhere, any day, any time! All of our garage door repair technicians are trained to meet our very high quality standards. Join the thousands of satisfied customers that have trusted the Red Ribbon Overhead Door Company of Pueblo™.
Whether you’re looking for garage door opener maintenance, garage door opener repair, or a brand new garage door opener, Sears Home Services can help. We’re your best, most-trusted option for fast, quick, and easy local service, repair, and maintenance of your automatic garage door opener. Whether your garage door won’t open or close, your garage door opener chain is broken, your automatic garage door opener won’t work after a power outage, your garage door won’t work when it’s cold, or your automatic garage door opener won’t stop running, we’ll connect you to the best local automatic garage door opener repair service technicians in the business. Technicians that are highly trained, licensed, vetted, nearby, and guaranteed to help fix all of your garage door opener needs. We have thousands of local technicians that are always “near me,” that can help you no matter what your appliance emergency.
10The type of garage door shown provides the necessary lift assistance with a “torque tube.” If you intend to use an opener, wait to install the tube. Otherwise, install the torque tube according to the manufacturer’s directions. Roll up the door about 4 feet to check for the alignment of the tracks, and make any adjustments. Then tighten all fasteners.