Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
Clint and James called and checked if my son had any problem with them showing up earlier than planned . No biggie there, they came, they examined , and they brought my sons busted garage door back up to a fully operation system . While the cost was more than myself or my son expected , the results were undeniable . A complete system review showed many worn or weak spots in his 14-15 year old bearings and such . They replaced what was needed and door works great . Next stop my house , all I needed was a replacement door seal . After talking with the tag team , I decided to go for the full Monty , and get an update to my bearings etc. Just to protect my wife in case I am not around to jack hammer a door open with a busted spring . Which would likely not work anyway ! Longer story short ...great outfit , good team , nice guys , job well done !! If you need any garage door work ...Precision Overhead Door is the place to call . Thanks very much for a great job guys ....Tedread more
Mike did an outstanding job replacing two torque-master spring assemblies for my double door garage. He arrived early, after calling to say he could do so, and offered a concise explanation of his very thorough safety inspection and diagnosis of my problem (one broken spring and another of suspect reliability). He then proceeded to swap out both torque masters with new torsion bar mechanisms in less than two hours. I found him personable, articulate, knowledgeable, and efficient. Honestly, my confidence in these newly installed devices has more to do with Mike than the products themselves. Thank you, Precision, for sending such a qualified professional to repair my garage doors. I will not hesitate to recommend your services to friends.read more
You can choose from three basic types of steel door: (1) steel only; (2) steel with insulation on the inside; and (3) steel on both sides with 1-3/8 to 2 in. of insulation. Other features that add to the cost are thicker insulation and windows, especially insulated windows. The do-it-yourself tensioning systems also add a little to the door’s cost. Be sure to specify exactly what you want.

Step 5: Check for loose hardware, and tighten as needed. On swing-up doors, check the plates where the spring is mounted to be sure the screws are tight, and tighten any loose screws. On roll-up doors, check the hinges that hold the sections of the door together; tighten any loose screws, and replace any damaged hinges. Sagging at one side of the door can often be corrected by servicing the hinges. If a screw hole is enlarged, replace the screw with a longer one of the same diameter, and use a hollow fiber plug, dipped in carpenters' glue, with the new screw. If the wood is cracked at a hinge, remove the hinge and fill the cracks and the screw holes with wood filler. Let the filler dry and then replace the hinge. If possible, move the hinge onto solid wood.
Ryan Fleming, Technician with Precision Door replaced a broken garage door spring at our home last night and I was so impressed with his knowledge, professionalism and positive attitude that I felt compelled to write this review. We have been customers of Precision Door for over 5 years and have always been pleased with how promptly and cost effectively they perform repair and maintenance work. I highly recommend both Ryan and Precision Door.read more
You'll never ask yourself that question again. Just look at your phone to know for sure. Most smart garage door openers will tell you if it's open or shut. They'll send a message every time your garage door is opened or closed too, if you like. Electric garage door openers provide a huge amount of convenience and safety. Imagine you're in a hurry, it's raining out, you pull out of the garage then press the button on your garage door opener remote. The garage door closes, and you didn't have to get out of your car.
Here is an odd problem that I cannot figure out. I am handy with electrical stuff, but this one has me stumped. My small kitchen appliances all work on a single circuit, with 5 outlets. One of those outlets has a 20Amp breaker built into it with a test and resent button (I never understood what the test button is for). I only have a toaster, a floor lamp and occasionally a coffee grinder plugged into the circuit. Suddenly, none of the outlets work. Nothing new, no new appliances, the whole circuit went dead. I noticed when I trigger the reset button, there is an immediate click and it goes out again. I have tripped and reset the main breaker on the circuit board in the garage, nothing. Power gets to the outlet, but it doesn't work and there is no electricity in any of the 5. I un plugged everything. Reset the breaker on the outlet. It clicked again immediately, still no electricity. I changed out the outlet, with a new one with breaker built in which I bought today at Home Depot. Same problem. I tested for electricity, the outlet with the built in breaker receives 120v electricity coming in, but it always seems to be shorted out and does not send it out. I assume that all of the 5 outlets are connected inline, so thinking that if I went one by one, I'd be able to find a short. I opened all of the boxes, checked everything and all looks clean, new, no problems. I completely disconnected the two outlets that are closest to the main one with thereset button and nothing.Help
Another key safety feature to prevent entrapment from garage doors is the “electric eye” sensor system found on many more modern garage door systems. Sensors placed on either side of the garage door’s track system about 4 to 6 inches off the ground transmit an infrared beam of light during a door’s closing operation. Should anything break the beam during the closing operation – including adults, pets or other objects – the opener should automatically stop and reverse the closing operation.

In addition to our damaged garage door repair services, we also provide and recommend preventative garage door maintenance in Bakersfield and communities throughout Kern County. Proactive maintenance is the best way to ensure your garage door is operating at its peak potential and that you put off costly repairs and replacement services as far into the future as possible.


As a first time homeowner, Home advisors is an invaluable tool! There is a steep learning curve that comes with buying a house!!!! Being able to have access to unbiased information is great! It really helps to have a basic idea of what costs are, and all the different things that go into each project. who knew that there was so much to consider when looking to replace garage doors!!!!
Looking to repair your garage door opener? Common problems could range from issues with the remote or wall switch that control the garage door opener to more serious issues like a grinding noise coming from the opener itself. If you need help with repairing your garage opener, schedule a repair appointment today! We repair all major brands and have same-day availability in most markets, so we can get your garage door opener repaired and running smoothly. To learn more about the cost of repairing garage doors, visit our garage door and opener installation and repair cost guide.
Wheel Track Obstruction – Try closing the garage door manually to see if there are obstructions on the wheel tracks. If that is not the case, examine your tracks for potential damage like dents and bends. Look at your door to see if it is hanging unevenly. If the track is damaged or the door is hanging unevenly, it is time to call a professional for repairs. Track repairs can typically cost $133 to $154. Cost for correcting the uneven hanging of doors themselves can vary greatly, but typically cost about $125.
Because garage door springs and openers can degrade over time, it’s important to occasionally test this safety feature. With the garage door open, place a solid object such as a 2-by-4 board or a cinder block where the door will close. Never test any safety feature using your or another person’s body. With the board or block in place, press the close button. If working properly, the garage door should close on the obstruction and immediately reverse the closing operation when it comes in contact with it.
"We had an unusual repair requirement. We have horizontal sliding steel doors on our 1950's equipment shed. The upper track was damaged by a roofer's forklift while they were loading supplies onto the roof. The track is made out of very heavy steel, not like the track in today's doors. Toby, responded to my request very quickly and came out of his way to inspect the damage. Although it was not something that he had encountered before, he was able to fix the track and the door is operating better than it has in years. Thank you."
×